Laser Ignition System Seminar Report and PPT

Definition

Drawbacks Of Conventional Spark Ignition

Location of spark plug is not flexible as it require shielding of plug from immense heat and fuel spray.

It is not possible to ignite inside the fuel spray.

It require frequent maintenance to remove carbon deposits..

Leaner mixtures cannot be burned.

Degradation of electrodes at high pressure and temperature.

Flame propagation is slow.

Multi point fuel ignition is not feasible.

Higher turbulence levels are required.

What Is Laser?

Lasers provide intense and unidirectional beam of light. Laser light is monochromatic (onespecific wavelength). Wavelength of light is determined by amount of energy releasedwhen electron drops to lower orbit. Light is coherent; all the photons have same wavefronts that launch to unison. Laser light has tight beam and is strong and concentrated. Tomake these three properties occur takes something called “Stimulated Emission”, inwhich photon emission is organized. Main parts of laser are power supply, lasing medium and a pair of precisely aligned mirrors. One has totally reflective surface and other is partially reflective (96 %). The most important part of laser apparatus is laser crystal. Most commonly used laser crystalis manmade ruby consisting of aluminum oxide and 0.05% chromium. Crystal rods are round and end surfaces are made reflective.

A laser rod for 3 J is 6 mm in diameter and70 mm in length approximately. Laser rod is excited by xenon filled lamp, whichsurrounds it. Both are enclosed in highly reflective cylinder, which directs light fromflash lamp in to the rod. Chromium atoms are excited to higher energy levels. The excitedions meet photons when they return to normal state. Thus very high energy is obtained inshort pulses. Ruby rod becomes less efficient at higher temperatures, so it is continuouslycooled with water, air or liquid nitrogen. The Ruby rod is the lasing medium and flashtube pumps it.

Ruby Laser

Laser Induced Spark Ignition

The process begins with multi-photon ionization of few gas molecules which releaseselectrons that readily absorb more photons via the inverse bremsstrahlung process toincrease their kinetic energy. Electrons liberated by this means collide with othermolecules and ionize them, leading to an electron avalanche, and breakdown of the gas.Multiphoton absorption processes are usually essential for the initial stage of breakdownbecause the available photon energy at visible and near IR wavelengths is much smaller than the ionization energy. For very short pulse duration (few picoseconds) themultiphoton processes alone must provide breakdown, since there is insufficient time forelectron-molecule collision to occur. Thus this avalanche of electrons and resultant ionscollide with each other producing immense heat hence creating plasma which issufficiently strong to ignite the fuel. The wavelength of laser depend upon the absorptionproperties of the laser and the minimum energy required depends upon the number ofphotons required for producing the electron avalanche.

The minimum ignition energy required for laser ignition is more than that for electric spark ignition because of following reasons: An initial comparison is useful for establishing the model requirements, and for identifying causes of the higher laser MIE. First, the volume of a typical electrical ignition spark is 10^-3 cm3. The focal volume for a typical laser spark is 10^-5 cm3. Since atmospheric air contains _1000 charged particles/cm3, the probability of finding a charged particle in the discharge volume is very low for a laser spark. Second, an electrical discharge is part of an external circuit that controls the power input, which may last milliseconds, although high power input to ignition sparks isusually designed to last <100 ns. 

Breakdown and heating of laser sparks depend only onthe gas, optical, and laser parameters, while the energy balance of spark dischargesdepends on the circuit, gas, and electrode characteristics. The efficiency of energytransfer to near-threshold laser sparks is substantially lower than to electrical sparks, somore power is required to heat laser sparks. Another reason is that, energy in the form of photons is wasted before the beam reach the focal point. Hence heating and ionizing the charge present in the path of laserbeam. This can also be seen from the propagation of flame which propagates longitudinally along the laser beam. Hence this loss of photons is another reason forhigher minimum energy required for laser ignition than that for electric spark.

Advantages

 Location of spark plug is flexible as it does not require shielding from immense heat and fuel spray and focal point can be made any where in thecombustion chamber from any point It is possible to ignite inside the fuel spray asthere is no physical component at ignition location.

 It does not require maintenance to remove carbon deposits because of itsself cleaning property.

 Leaner mixtures can be burned as fuel ignition inside combustion chamberis also possible here certainty of fuel presence is very high.

 High pressure and temperature does not affect the performance allowing the use of high compression ratios.

Flame propagation is fast as multipoint fuel ignition is also possible.

 Higher turbulence levels are not required due to above said advantages